|
| |
|
|
Solution of bendig technology problems of thinn walled profiles
Matoušek, Karel ; Forejt, Milan (referee) ; Samek, Radko (advisor)
Reconnaissance of problems and parameters of square hollow profile bend. Finding (identification) of deformation of cross-section. Finding of suitability of unannealed material for component part. Finding of mechanical characteristics of welds and influence of their bend position. This finding was done on the basis of comparison of tensile tests and consequently aplicated to specific part where the suitability for use of unannealed material were proved.
|
|
|
Assemblying effect on cable lines quality
Dočkal, Martin ; Křepelka, Václav (referee) ; Filka, Miloslav (advisor)
In the first part is explained what actually a structured cabling is. Its beginning, from what and why it was created. Its history when at the beginning were applied unbalanced coaxial cables, those were later replaced by balanced cables. In cabling for TVs are still used coaxial cables. Balanced cables are according to type named UTP, STP, FTP, and so on. Whit growing popularity of this type of cabling and its wide spread application was necessary to set some rules, standards, specifications and demands, how to build up the cabling from project to realization. According to these rules is the system built so there are strict rules for length of subsystems and interfaces and the whole appearance of the structure cabling. Next important point is projecting of cabling that is related to the previous points and when it’s finished, we should strictly follow it. With the project is closely connected characteristic of this cabling as attenuations, cross-talks and other transmission parameters which are measured in the practical part. In the second part is spoken about all the parts of which the structured cabling consists - metallic and optical connecting elements and cables. There are also mentioned their mechanical, electrical and transmission features. In the third part is described influence of man on the quality of structured cabling and the most common causes of lower quality and the ways how to prevent this from happening and how to manipulate with cabling not to destroy it. The final (fourth) part considers the measurement. There are measured qualities of metallic wires as the attenuations, delay, cross-talks on the near- and far-end, impedance and resistance. To all the features are mentioned schemes of the measurement on the twisted pairs. The measurement is divided into two parts. In the first part are measured five types of balanced cables of different length, category and damage influencing quality of these cables. In the second part is measured one balanced cable if it’s corresponding with category 5 for that t was made and if it would be possible to use it also for higher category 6. Values are tabularly sorted in tables.
|
|
|
Solution of bendig technology problems of thinn walled profiles
Matoušek, Karel ; Forejt, Milan (referee) ; Samek, Radko (advisor)
Reconnaissance of problems and parameters of square hollow profile bend. Finding (identification) of deformation of cross-section. Finding of suitability of unannealed material for component part. Finding of mechanical characteristics of welds and influence of their bend position. This finding was done on the basis of comparison of tensile tests and consequently aplicated to specific part where the suitability for use of unannealed material were proved.
|
|
|
Assemblying effect on cable lines quality
Dočkal, Martin ; Křepelka, Václav (referee) ; Filka, Miloslav (advisor)
In the first part is explained what actually a structured cabling is. Its beginning, from what and why it was created. Its history when at the beginning were applied unbalanced coaxial cables, those were later replaced by balanced cables. In cabling for TVs are still used coaxial cables. Balanced cables are according to type named UTP, STP, FTP, and so on. Whit growing popularity of this type of cabling and its wide spread application was necessary to set some rules, standards, specifications and demands, how to build up the cabling from project to realization. According to these rules is the system built so there are strict rules for length of subsystems and interfaces and the whole appearance of the structure cabling. Next important point is projecting of cabling that is related to the previous points and when it’s finished, we should strictly follow it. With the project is closely connected characteristic of this cabling as attenuations, cross-talks and other transmission parameters which are measured in the practical part. In the second part is spoken about all the parts of which the structured cabling consists - metallic and optical connecting elements and cables. There are also mentioned their mechanical, electrical and transmission features. In the third part is described influence of man on the quality of structured cabling and the most common causes of lower quality and the ways how to prevent this from happening and how to manipulate with cabling not to destroy it. The final (fourth) part considers the measurement. There are measured qualities of metallic wires as the attenuations, delay, cross-talks on the near- and far-end, impedance and resistance. To all the features are mentioned schemes of the measurement on the twisted pairs. The measurement is divided into two parts. In the first part are measured five types of balanced cables of different length, category and damage influencing quality of these cables. In the second part is measured one balanced cable if it’s corresponding with category 5 for that t was made and if it would be possible to use it also for higher category 6. Values are tabularly sorted in tables.
|
|
| |
guest ::
